Home > Hp Scanjet > Hp Scanjet 4070 Lamp Error

Hp Scanjet 4070 Lamp Error

note: The TMA cable must be connected to perform a self test on the HP Scanjet 4800 series because the buttons to start the test are located on the TMA (document If the base unit self test results were as described above, then the test was successful. Leave the power module connected to the power source. Jophin Joy 38,202 views 7:00 Hp Color Laserjet 2840 Scannerfehler 5.avi - Duration: 9:03. this contact form

Nguyễn Mạnh Tùng 35,829 views 2:03 How to Salvage Usefull Parts from Printers and Scanners - Duration: 11:13. During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. Restart the PC and the scanner ...

You can change this preference below. HP Scanjet 4200 Disconnect the USB and power cables from the back of the scanner. Press and hold the Scan and Scan Film buttons on the front panel, and set the power switch to the On position. Lamp burned out!

  1. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual .
  2. Loading...
  3. IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product Warranty Result
  4. Press and hold the Copy and E-mail buttons, and connect the power cable to the scanner.
  5. Lift the document cover.
  6. Close Learn more You're viewing YouTube in English (UK).
  7. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd.

You can try disassembling the scanner and check that ... Your cache administrator is webmaster. Sign in to add this to Watch Later Add to Loading playlists... Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual .

If the base unit self test results were as described above, then the test was successful. Disconnect the USB Interface cable and the ADF Accessory cable from the back of the scanner. To end the test, disconnect the power cable from the back of the scanner. Leave the power module connected to the power source.

If not, then it is most likely bad. Z7_3054ICK0KGTE30AQO5O3KA3015 hp-online-communities-portlet Actions ${title} Loading... With the power module connected to the power source, connect the power module cable to the back of the scanner. Please try the request again.

Press and hold the Copy and E-mail buttons on the front panel, and connect the power cable to the scanner. HP Scanjet 7400c, 7450c, and 7490c Disconnect the USB and power cables from the back of the scanner. Lift the document cover. To end the test, disconnect the power cable from the back of the scanner.

For the cost ... weblink You can certainly get a replacement lamp but due to the complexity of replacing it I recommend you get a new scanner. Diagnostic speeds options are 75, 150, 200, 300, 600, 1200, 2400, or 4800 PPI. The system returned: (22) Invalid argument The remote host or network may be down.

It will occasionally work if I unplug and re-plug it. The bulb needs replacing. Question about HP ScanJet Scanners 1 Answer Hp scanjet 3970 on Mac: lamp error hp scanjet 3970 on Mac: lamp error Normally this error means that your lamp will no longer http://technewsonline.net/hp-scanjet/hp-scanjet-3800-lamp-error.html After a few seconds, the carriage will continuously move the full length of the scanning bed.

During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. Press and hold the E-mail and Copy buttons at the same time. During a successful base unit self test, the scanner will do the following: The scanning lamp will light up.

Flatbed Scan Emulation Exerciser – Press the Edit Text (OCR) button – This will begin a continuous flatbed scan at designated speed.

During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. Filter By: 3500c script c00022537 readiris feedrer software classcode 2400 bps05721 4400c 80004005 line 3970 27 questions posted Ask a Question Usually answered in minutes! Leave the power module connected to the power source. Working...

During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. Scanner self tests test the following: The ability to turn on the scanning lamp. HP Scanjet 4600 and 4670 Disconnect the multi-function cable from the USB port. his comment is here HP Scanjet 2300 and 3670 Disconnect the Universal Serial Bus (USB) and power cables from the back of the scanner.

Uploaded on 31 Oct 2011Parts Available @ www.BrokenPrinter.com hp 3300 or 3330 scanner bulb warming up error how to fix and repair the hp 3380 warm up problem Category Education Licence Connect the power adapter cable to the back of the scanner. Have a manual for HP Scanjet 4070 Flatbed Scanner? This feature is not available right now.

Expand Popular Products HP ScanJet 2400 Flatbed Scanner 249 Questions HP Scanjet 5590 Flatbed Scanner 110 Questions HP ScanJet 3200C Flatbed Scanner 88 Questions HP Scanjet 4470c Flatbed Scanner 72 Questions To end the test, disconnect the power cable from the back of the scanner. Rudi M 42,690 views 10:05 Canon Scanner: Equipment Autopsy #37 - Duration: 22:33. HP Scanjet 8200 To enter diagnostics mode: Disconnect the power supply from the back of the scanner base.

Tthe carriage will start moving back and forth in the full scan bed length.