Home > Hp Scanjet > Hp Scanjet 3770 Lamp Error

Hp Scanjet 3770 Lamp Error

Sign in to add this to Watch Later Add to Loading playlists... The Grand Tour Premieres November 18th Amazon.co.uk Try Prime Electronics & Photo All Departments Alexa Skills Amazon The carriage will continuously move the full length of the scanning bed. TigerDirect 101,974 views 4:53 Got an old Flatbed Scanner? Autoplay When autoplay is enabled, a suggested video will automatically play next. this contact form

Details Dispatched from and sold by Digidave. Unplug the power cable from the power source, wait 60 seconds, and then plug it back in. Clean the scanner glass. EduardoGon 3,433 views 2:00 Details HP scanjet G4050 photo color flatbed scanner 4800x9600 dpi 96-bit usb Deal - Duration: 1:36.

Disconnect the USB Interface cable and the ADF Accessory cable from the back of the scanner. Power cylcle the scanner to cancel the test. Warranty status:Unspecified Check warranty status Enter product serial number The serial number you entered,, matches a different product than the current product.

It would cost more to replace the scanner assy than a new ... Thiago Cordeiro 2,557 views 10:10 HP SCANJET 2300C SCANNER RED LIGHT PROBLEM - Duration: 3:08. Loading... While pressing the “E-mail” and “Copy” buttons, reconnect the power supply to the scanner.

The adapter has a short warm-up mode. The scanning lamp will stay lit, and the carriage will continuously move the full length of the scanning bed. If the base unit self test results were as described above, then the test was successful. which part doesn't work?

The TMA should turn on for three seconds and then turn off. See the HP Image Zone onscreen help for more information. The carriage will return to the home position. The carriage will continuously move the full length of the scanning bed.

Lift the document cover. Visit Website If there is not enough hard-disk space, remove unnecessary files or install the software on a different disk drive. Your recently viewed items and featured recommendations › View or edit your browsing history After viewing product detail pages, look here to find an easy way to navigate back to pages HP Scanjet Scanners - Performing a Base Unit Self Test Introduction A base unit self test is a quick, simple, and effective way to test the basic hardware functionality of an

Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading... weblink I think the belt jumped of motor, but I don't know. Tthe carriage will start moving back and forth in the full scan bed length. The scanned image is black even though the adapter light is on From the Basic menu in the HP Image Zone software, click Lighten/Darken.

  1. During a successful base unit self test, the scanner will do the following: The scanning lamp will light up.
  2. Yup!
  3. Change your region to 'UK - BFPO’ below: Or Add to List Have one to sell?
  4. dottotech 5,499 views 7:03 Hp Scanjet G Series Photo Scanners - Duration: 5:58.
  5. If not, proceed with the next step.
  6. Question about HP ScanJet Scanners 1 Answer Lamp error lamp error Cannot initialize because of lamp error, is this a hardware error.
  7. Sign inYour AccountTryPrimeYourLists Basket0 Your Amazon.co.ukToday's DealsGift Cards & Top UpSellHelp Electronics Best Sellers Deals Phones & Accessories TVs & Home Cinema Camera & Photo Audio & HiFi Computers Wearable Technology

Question about HP ScanJet Scanners 1 Answer I'm getting a lamp error on my 2400. Connect the power adapter cable to the back of the scanner. alexsilwaribeiro 1,035 views 2:47 Scanner Photo HP Scanjet G4050 - www.iris.ma - Duration: 5:58. http://technewsonline.net/hp-scanjet/hp-scanjet-3800-lamp-error.html Sign in Share More Report Need to report the video?

If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services. Sign in to add this video to a playlist. Press and hold the Copy and E-mail buttons on the front panel, and connect the power cable to the scanner.

Question about HP ScanJet Scanners 2 Answers When I try to scan - I get a ...lamp error" message.

If the bulb is broken, service is required. To end the self test, set the power switch to the Off position. Connect the cable from the TMA (document cover) to the TMA port on the back of the scanner base unit. The scanned images are dark Check to see if the adapter light is on before clicking New Scan or Accept.

Please endure that the scanning device is connected properly and try again. HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading... After 60 seconds, reconnect the power cord to the scanner, and then turn on the computer, in that order. his comment is here If the base unit self test results were as described above, then the test was successful.