Home > Hp Psc > Hp Psc 1350 Error Reset

Hp Psc 1350 Error Reset

Fechar Saiba mais View this message in English Você está visualizando o YouTube em Português (Brasil). É possível alterar essa preferência abaixo. Figure 18: Secure the USB cable NOTE: Make sure that the USB cable is connected correctly. If these steps resolved the issue, you do not need to continue troubleshooting. It might take several tries to complete the sequence within ten seconds. this contact form

The money spent on the new cartridges was a waste, but if you can sell them to someone, do it. If you are using letterhead, insert the top of the page first. I think i should just throw them in the garbage because if i can get this printer working....im going to use the new ones anyways. That of 128mb of built in memory or higher. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c00095908

To reinsert, hold the cartridge by its sides, and then slide the cartridge forward into its slot at a slightly upward angle. Wait a minute before continuing on to the next step. Faça login para que sua opinião seja levada em conta. NOTE: If the alignment page fails to print, repeat the button-press sequence in this step.

  • I tried turning it off and on, disconnecting/connecting it to the computer, opening it to see if the cartridge would reset, all to no avail.
  • My toddler just broke ours and it doesn't look like the parts are available from hp anymore.Does anyone know if there's another acceptable replacement part or another place to get one
  • I am going mad!!
  • With the power on, disconnect the power cord from the rear of the product.
  • Close the cartridge access door.
  • Press and release the Copies button.
  • maybe from trying to print & cancel the print jobs ..something happened to the printer...i dont know because i cant remember if the E was on there when i turned it
  • Disconnect the USB cable from the rear of the product.
  • When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both the Cancel button () and the On/Resume button ().

Look inside the product to see where the carriage is stuck, and then check for any torn paper or objects that might be restricting the carriage. A sequence of buttons on the control panel must now be pressed in the order presented. This video shows how to clear a paper jam from the All-in-One

Click here to see this video in full screen on YouTube. KingPin1000, Aug 21, 2008 #12 arknorth Joined: Oct 17, 2007 Messages: 1,099 Changing back to 1 means that it was ready to work for that brief moment - odd.

Thanks for your response so far!Dazz UK by hpwizard on Oct 24, 2006 at 2:25pm Add comment Please sign in to comment 0 Dazz,Sorry I missed your post in October 06.If And then I pulled the paper out of it. If the issue persists, continue to the next solution.

Carregando...

When the printer is turned on, the scanning wand should move slightly and possibly blink momentarily. Press the Scan button to try the scan job again. The alignment page prints. If the LED does not light up, contact HP to replace the power module.

Also try one last attempt at a hard reset - while holding the CANCEL button down, press the power button until the unit shuts down. If the issue persists, continue to the next solution. lol. Figure 42: Insert the cartridge Firmly push the cartridge in until it snaps into place.

by fshrmn on Jul 15, 2008 at 12:46pm Add comment Please sign in to comment 0 The ALT+Spacebar+Minimize solution has allowed me to see my all-important HP Director dialog box again weblink Please help... Remove and clean each cartridge one at a time. Trying to clear jammed paper from the front of the product can damage the print mechanism.

I keep getting an "out of paper" error but clearly I'm not out of paper! A-N arknorth, Aug 14, 2008 #2 KingPin1000 Thread Starter Joined: Mar 19, 2006 Messages: 166 hi...thanxs for replying. However, many software errors can be fixed with a hard reset, but do know that many changed settings will go back to the factory settings for the HP PSC 1315. navigate here The black cartridge is only a few weeks old andwas fine til that day.

That killed it forever! Removed the envelope and tried again, same result no goDecided to not print an envelope but another document. What kind of cleaning agent should be used to clean the accumulation of grease?

CAUTION: Do not force the paper to move too far forward in the tray.

I wish i hadnt bought these new cartridges...but they told me i had too because we tried everything with the old ones..and nothing worked. When I go to print, it has the message: "Error:fatal: Opening Printer Connection Failed: Unable to open the printer connection. Solution six: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. If the product does not turn on automatically, press the On/Resume button () to turn the product back on.

Shortly before this problem began, I had installed the driver update suggested by hp. If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product. by unknown on Dec 3, 2004 at 3:30am Add comment Please sign in to comment 0 The HP PSC 1300 series has a higher minimum system resource specification. his comment is here Solution three: Install the HP software You must download and then install the HP product software in order for your computer to detect the product.