Home > Hp Psc > Hp 1350 Printer Check Print Cartridge Error

Hp 1350 Printer Check Print Cartridge Error

Contents

Figure : Open the cartridge access door Press lightly on the top of the cartridge that you are removing to release it from its slot. The sequence must be completed within ten seconds. Issue: The On/Resume and Black Start Copy lights blink In this normal condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinking Check Paper light: Off Check This video shows how to print a test page Click here to see this video in full screen on YouTube. Check This Out

Reply 0 0 AmerEagle Intern Posts: 27 Member Since: ‎01-29-2012 Message 6 of 7 (1,401 Views) Report Inappropriate Content Glad You're Back, Re: HP 1310 Series (1315xi) Red Blinking Cartridge Light, If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product. If these steps resolved the issue, you do not need to continue troubleshooting.

Hp 1350 Printer Check Print Cartridge Error

This video shows how to print a test page Click here to see this video in full screen on YouTube. Press and release the Copies button. Try the intended task again.

  1. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.
  2. The illustration below shows these contacts.
  3. note: If the alignment page fails to print, repeat the button-press sequence in this step.
  4. Remove the cartridge and place it on a piece of paper with the nozzle plate facing up.
  5. note: You might need a flashlight to illuminate areas for proper viewing.
  6. If the issue persists, continue to the next solution.
  7. Hi,Turn the printer offUninstall the printer & all related softwareRestart your computerReinstall the printerThen you should be able to print fineThanks,Robert Preston Ask Your Own Printers Question Customer: replied6 years ago.
  8. I had already done all of your suggestions, but have done them again and it has not resolved the problem Expert: Sowrav D.

note: If the carriage does not move into the access area, turn the product off and then on again. Figure : HP PSC 1200, 1310, 1340, and 1350 control panel with the lights indicated On/Resume light Check Paper light Check Print Cartridge light Copies display (where an 'E' might display) Figure : Remove the black cartridge Close the cartridge access door. Hp Psc 1350 Manual Issue: The Check Paper light blinks In this error condition, the following blinking lights pattern displays on the control panel: On/Resume light: On Check Paper light: Blinking Check Print Cartridge light:

If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1210 Check Print Cartridge Error Plug the alternate power cord into the wall outlet. If you have a defective cartridge or printhead, it might be under warranty. Step two: Align the cartridges Follow these steps to align the cartridges.

The ink can dry and clog the nozzles if the cartridge is outside of the printer for too long.Unplug the printer.Dip a swab in the clean water, then squeeze it to How To Reset Hp Psc 1410 Printer If the issue persists, continue to the next solution. Issue: The On/Resume light blinks In this normal condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinking Check Paper light: Off Check Print Cartridge light: Off This video shows how to clear a carriage jam Click here to see this video in full screen on YouTube.

Hp Psc 1210 Check Print Cartridge Error

When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Plug the power cord back into the wall outlet. Hp 1350 Printer Check Print Cartridge Error Reconnect the power cord to the rear of the product. Hp Psc 1210 Troubleshooting This tool will detect HP PCs and HP printers.

Do not print on paper with paper clips or staples attached. his comment is here Trying to clear jammed paper from the front of the product can damage the print mechanism. When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Press the On/Resume button () to turn on the product. Hp Psc 1315 Check Printer Cartridge Error

First Time Here? The alignment page prints. Step two: Align the cartridges Follow these steps to align the cartridges. this contact form The sequence must be completed within ten seconds.

The carriage moves to the center of the product. Hp Psc 1350 Troubleshooting Try the steps below to identify the problem cartridge: Open the cartridge access door. If these steps resolved the issue, you do not need to continue troubleshooting.

If these steps resolved the issue, you do not need to continue troubleshooting.

This video shows how to clear a carriage jam Click here to see this video in full screen on YouTube. Figure : Open the cartridge access door Wait until the product is idle and silent, and then disconnect the power cord from the rear of the product. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. Hp Psc 1210 Reset Press the On/Resume button () to turn on the product.

Press the On/Resume button () to turn off the product. Figure : Snap the cartridge into place Repeat these steps to insert the other cartridge into its designated slot. If the issue persists, continue to the next solution. http://technewsonline.net/hp-psc/hp-psc-1350-error-reset.html Open the scanner lid.

Close the cartridge access door. Step two: Align the cartridges Follow these steps to align the cartridges. An alignment page prints automatically. Solution three: Install the HP software You must download and then install the HP product software in order for your computer to detect the product.

Load plain, white paper into the paper tray. Place your index finger in the finger slot on the paper tray at the front of the product. Problem started about the same time as some forumdiscussions about Automatic Update trying and not being able to install .NET framework 5.3, which is in my Add/Remove, but A.U. Press the On/Resume button () to turn off the product.

Press the Cancel button () on the control panel.