Hp Print Error 13.0000
Check the pickup feed and separation rollers for unusual wear. I bypassed the rear door interlock so I could watch the process and noticed the registration or feed roller not turning during the print cycle. TheRealDrBullshit 37.060 görüntüleme 28:19 Fixing a HP LaserJet by baking the formatter board in oven. - Süre: 8:15. Add memory to printer or reduce complexity of print job On the 5P turn the image adapt and page protect to ON or AUTO. http://technewsonline.net/hp-print/print-job-won-39-t-delete.html
how to fix, or which replacement part? - waleedasif322 Please sign in to comment HP Color LaserJet CP2025 Buy discount ink Buy this printer More HP questions © Copyright 2011-2016, FixYourOwnPrinter.com, Yes, I should be able to try a tray swap - I will verify that this eventing and if so give it a try.Thank You, Reply 0 0 « Message Listing Reseat the PostScript SIMM and/or replace it. Listen for the motor operation, make sure it's operational.
San Rafael, CA Great that you have that part in stock and thank you for your quick reply. If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services. On the 5L, set the Enhanced I/O to AUTO (PCL mode) and resend the print job. Call us 608-831-2396 for more information. Message on printer displayWhat it meansWhat to do 13.XX PAPER JAM [LOCATION] Media is jammed at the specified location (and possibly at other locations).
If worn, replace. You can change this preference below. On the IIP/IIIP this can be caused by a defective toner cartridge, defective cooling fan, PS4 or PS5 sensors. Error 30 PS Error 16 ALL PRINTERS An I/O time-out or a prompt for user interaction like a manual feed has been exceeded.
Sıradaki HP CLJ CP2025 HP CLJ Pro 400 M451 Pick Roller Change - Süre: 7:17. Warranty status:Unspecified Check warranty status Enter product serial number The serial number you entered,, matches a different product than the current product. Check these items. Works great and certainly solved the problem (as I expected it would). -Alan A.
If the problem persists and is application specific, verify proper setup with application vendor. Home | contact Us | About Us | Terms of Sale | FAQ | HP Maintenance Kits | HP Fuser Assemblies | HP Color Supplies |HP Parts Lexmark Maintenance Kits | If the error stays with the original printer, then the printer needs to be service.Information on how to contact HP is located here.Best Regards,Kazman KazmanI am an HP EmployeeSay Thanks by Power cycle the printer.
On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software.
Restart printer. http://technewsonline.net/hp-print/hp-printer-error-codes.html Pro Slate 12) OR Browse all HP products Please wait while we process your request. Replace this as an assembly. Daha fazla göster Dil: Türkçe İçerik konumu: Türkiye Kısıtlı Mod Kapalı Geçmiş Yardım Yükleniyor...
Replace the Fan. X = Description 4 Printer Fan 7 Duplex Fan 1. Occasionally it will push a sheet through, usually when I just hit OK to clear jam and the engine cycles, but not enough to use the printer at all. http://technewsonline.net/hp-print/hp-print-assistant-download.html There is actually no physical paper jam, however something triggers the event, which will not reset apart from the toner remove/restore. (We have also tried replacing the toner cartridge) These events
Video kiralandığında oy verilebilir. Can also indicate a mis feed or paper not being picked up. Below is a full list of issues addressed in this firmware update, release on February 1st, 2012. Datecode: 20120123 HP LaserJet Pro 300/400 color M351/M451 Series Firmware Enhancements and Fix
Open and close the top cover to clear the message. 6.
Replace or clean as needed. Kapat Daha fazla bilgi edinin View this message in English YouTube 'u şu dilde görüntülüyorsunuz: Türkçe. Scroll through items until "I/O =" appears and use the +/- key to display parallel and the enter key to select. Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again.
Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Also check the toner level sensor and the toner cartridge itself for damage. Check the transfer roller and small media belt to ensure they are operating and can feed print media into the fuser. 2. his comment is here On rare occasions a defective paper control assembly or actuator can cause this problem.
ERROR 41 Momentary error, press "Continue" or "GO" to reset the printer 5L/6L Power Cycle the printer if error continues reseat the DC controller to Formatter 5P/6P Occurs if printer picks Verify the paper tray is fully closed. 3. Check the entire paper path for other pieces of media in the path. 2. Try removing and reseating the fuser. 5.
It will print single sided print jobs without issue. Back back to top How did we do? Can also be DC controller. 5Si/4+/4Si/IIISi (X=2, 3 or 4) Fan motor faulty, check fan number X or duplexor fan and replace as necessary 5 Main motor failure - replace main Showing results for Search instead for Do you mean or Post new question Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this
Reseat the cable and use only high quality IEEE 1284 compliant cables. 5Si Are you using a non-HP MIO device? Error 22 Error/ I/O Config Error/ Par I/O Error/MIO Error 22 EIO X BUFFER OVERFLOW The EIO card in slot X has overflowed it's buffer and data loss will occur 22 If the problem continues, remove the optional interface card and set the printer for standard parallel interface by taking off-line and holding down "Menu" key for 5-10 seconds. This can generally get you 100 or so more pages.
Replace any defective sensors or flags. 4. John D.