Hp Officejet Pro 8100 Printer Troubleshooting
Solving Processor Problems Poor performance is experienced. Solving Diskette Problems Diskette drive light stays on. In the audio driver or application software, reconfigure the jack or set the jack to its default value. Replace the system board. Check This Out
Figure : Do not touch the electrical contacts or nozzles on the printhead Figure : Remove the printhead Put the printhead (with the cartridges still installed) on its side on a If the printer does not turn on by itself, press the Power button to turn it on. Power on the system. A plug and play board may not automatically configure when added if the default configuration conflicts with other devices. http://support.hp.com/us-en/document/c02906379
Hp Officejet Pro 8100 Printer Troubleshooting
Diskette is damaged. Select Properties then select the Tools tab. Figure : Open the cartridge access door and the printer lid Push the old cartridge inward to release it, and then pull it toward you to remove it from its slot.
- Press the Power button to turn on the printer, if it is not already on.
- If the printer does not print a test page, there is an issue with the printer hardware.
- Replace the system board.
- On the Windows Vista Desktop, click Start, click the arrow on the lower right corner of the Start menu, then select Shut Down.
- The audio device may be connected to the wrong jack.
- Paper was added to a stack already in the tray while the HP product was printing.
- System does not power on and LEDs are not flashing.
Press the Power button to turn on the printer. note: If the page displays in the wrong country/region or language, click the Region - Language link in the upper right corner of your browser. None required. Hp Officejet Pro 8100 Reset Step two: Print a self-test report Print a self-test report.
warning: Do not reach into the cartridge access area at this time. Hp Officejet Pro 8100 Wireless Light Blinking Slide the new cartridge into its slot, and then gently push it forward until it clicks into place. WARNING: Do not reach into the cartridge access area at this time. If the 50.1 error does not go away with a working fuser in place, you need to replace the Low Voltage Power Supply.
Contact an authorized service provider. Hp Officejet Pro 8100 Flashing Wireless Light Replace the system board. Restart computer. To enable Wake-on-LAN in Windows XP: Select Start > Control Panel.
Hp Officejet Pro 8100 Wireless Light Blinking
caution: Do not leave the cartridges outside of the printer for an extended period of time. The removable hard drive has no power to the hard drive enclosure. Hp Officejet Pro 8100 Printer Troubleshooting Unplug the power cord from the wall outlet. Hp Officejet Pro 8100 Ink Lights Blinking Cause Solution Disc not properly seated in the drive.
Causes The following factors can cause paper jams: Paper loaded incorrectly in the paper tray. http://technewsonline.net/hp-officejet/hp-officejet-6310-all-in-one-printer.html The product lights might flash and the carriage might move. Restart the computer by pressing the power button. Reconnect the USB cable, and then try to print again. Hp Officejet Pro 8100 Printhead Error
Install a TXT capable processor. Cause Solution Jack has been reconfigured in the audio driver or application software. Replace module with the correct industry-standard device for the computer. http://technewsonline.net/hp-officejet/hp-officejet-pro-k5400-troubleshooting.html Figure : Do not touch the electrical contacts or nozzles on the printhead Clean the printhead contacts with a cotton swab.
Sign In Upload Page of 112 Go Download Table of ContentsContents Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Comment Manuals Brands Compaq Manuals Desktop 8100 - Elite Hp Officejet Pro 8100 Symbols When you remove the original printhead, insert the new printhead and cartridges within five minutes. Issue: All lights are off The following light pattern displays on the printer control panel: All lights: Off Figure : All lights are off Cause The printer is turned off, or
Reconnect the power cord from the rear of the printer.
Cause Solution Software volume control is turned down or muted. Replace the graphics card. If the issue persists, continue with the next solution. Hp Officejet Pro 8100 Ink Reset If the printer does not turn on by itself, press the Power button to turn it on.
If the error persists after replacing memory modules, replace the system board. 213-Incompatible Memory Module in Memory Socket(s) X, X, ... Cause Solution The font you are using does not support that particular symbol. None Computer on. http://technewsonline.net/hp-officejet/hp-officejet-5610-troubleshooting.html Open My Computer (Windows XP) or Computer (Windows Vista and Windows 7), right-click on the corresponding drive icon, and select Eject.
Refer to Appendix A, POST Error Messages for more information. Use both hands to pull any whole sheets of paper to avoid tearing them. If the error still persists, replace the system board. 2232-AMT error during MEBx execution Error occurred during MEBx execution which fails into “AMT” grouping. Reinstall the printer on top of tray 2.
Ensure that the cable is securely attached to the network connector and that the other end of the cable is securely attached to the correct device. Solution one: Check the indicated cartridges Follow these steps to check the cartridges indicated on the control panel. Wait until the carriage is idle and silent before proceeding. Power LED flashes Red six times, once every second, followed by a two second pause, and the computer beeps six times. (Beeps stop after fifth iteration but LEDs continue flashing.) Cause
Red Power LED flashes eleven times, once every second, followed by a two second pause. Cause Solution The system is trying to start from a diskette that is not bootable. The default mode is POST Message Disabled. Step one: Turn the printer off and on again Press the Power button () to turn off the product.