Home > Hp Laserjet > Hp Laserjet Iip Error 12

Hp Laserjet Iip Error 12

Connect a voltmeter between the 2 outside pins (1 and 14) on J212 (a long 14 pin socket on the DC controller board). Check paper path especially operation of PS1 5P Temporary errors occur if 2 pieces of paper were picked. Verify SIMM's are seated properly, replace defective SIMM's or install add'l SIMM's. 60 Service 2686A/D, LJ4, 4+, 4P Replace formatter PCB 60 Memory IIISi, 4S, 4V Bad SIMM memory. Output selector knob is not in duplex position. this contact form

Since, I believe, it'll claim the cover is closed even without a toner cartridge in place, I think it's the former. Install new toner cartridge. 2. test 9. Dirty or obstructed paper path.

LJ4P, 5P Top cover open. X=1: Beam detect malfunction. 2. I think reinspecting the connections is a good suggestion which I intend to pursue. by Russ Wrigh » Sat, 10 May 1997 04:00:00 Also 2 things 1 : The exhaust fan may not be rotating or is too slow, it must run at all times

Reproduction of this document in whole or in part is permitted if both of the following conditions are satisfied: 1. Check that ROMs are in correct location and orientation. 3. Inspect the Fiber Optics Cable for cuts or kinks. 2. Note 2686D: If one clutch needs re-greasing it is likely that they all do. 4.

You can probably fix that by taking out the LV power supply, taking it apart and examining the switch and its connections. HP LJ IIP - Error 12 OPEN OR NO EP 8. Replace laser PCB II, IID Replace memory PCB III, IIID 53-1 - Error in front memory slot. http://www.fixyourownprinter.com/posts/17166 Replace DC Controller PCA. 57.2 ERROR 1.

Paper pickup clutch turning more than once? Cycle power on the printer. 2. Or should I just order them both. About $40.

PS402 on front door PCA under transfer roller Bad DC controller PCB 16 Toner low All printers Toner uneven in cartridge Bad toner cartridge contact points Replace high voltage power supply. http://fixyourownprinter.com/posts/47478 by moe on Jun 22, 2001 at 6:07pm Add comment Please sign in to comment Please sign in to comment HP Color Copier 110 Buy discount ink Buy this printer More Best site on the web. Learn more You're viewing YouTube in English (United Kingdom).

Same as error 51 2686A/D Bad scanner assembly II, IID, III, IIID Bad cable laser/scanner to DC controller PCB Replace laser/scanner assembly IIP, IIP+, IIIP Bad scanner motor Bad DC controller http://technewsonline.net/hp-laserjet/hp-laserjet-4-plus-error.html I feel much better and a tat less stupid. Inspect Fiber-Optic Cable between Laser/Scanning Assembly and DC Controller. 3. If you don't get 24 V here, you have a LV power supply problem.

Out of spec media. 3. Respond to this 0 RG1-1604-000CN PC Board : Density adjust board - Includes cable assembly Part number RG1-1604-000CN is used in the following HP products.Product name HP model number(s)LaserJet IIP 33471AB, Sign in 74 3 Don't like this video? navigate here Replace MIO card. 3.

Replace Formatter PCA. 4. Sensor arm stuck or broken. 12 PRINTER OPEN 1. Replace Formatter PCA. 89 POSTSCRIPT ROM FAILURE 1.

Optional power stacker.

  1. Replace formatter PCA. 4000/4050/4100/5000/8000/8100 Only: 1.
  2. LJ4, 4+ Check and reseat laser scanner cable connections Replace laser scanner assembly 4V Check fiber optic cable from scanner to DC controller PCB Replace laser scanner assembly 4L, 4P, 5P
  3. Replace laser scanner assy Replace DC controller PCB LJ4, 4+ Check and reseat laser/scanner cable connections Replace laser scanner connections 4L, 4P, 5P Reseat scanner assembly Replace laser/scanner assembly 53 Error
  4. Just like getting an old girlfriend back.
  5. IIISi/4Si Only: 1.
  6. Bad fuser Exit Sensor (PS3). 5Si Only: 1.
  7. Cycle power. 68 COLD RESET 1.
  8. Resolve same Damaged fiber optic cable.
  9. Conection has been broken between printer and EIO/MIO card; try reseating EIO/MIO card 40.X Mio Error 5Si Only: 40.1 HP Mio port 1 (upper slot) 40.2 HP Mio port 2 (lower
  10. FONT COLOR="orange" size=4>4000/4050/4100/5000/8000/8100: 1.

is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.) IIP, IIP+, IIIP Only: 1. Sign in 4 Loading... Replace Paper Control PCA (Solenoid/Sensor PCB Assembly). 4. Replace fuser.

The capacitor is only rated at about 16 V. A contact or plastic tab me have broken off. KURTA IS /ONE 12" X 12" 5 post • Page:1 of 1 All times are UTC Board index Spam Report Remind me later Review A privacy reminder from YouTube, a Google his comment is here Replace Laser Diode Assembly. 3.

Now connect the meter between pins 2 and 13 on the same connector. Paper tray empty or not seated correctly. 2. You've saved me hundreds of $$$$. PCL file being sent to printer while in PostScript mode. 2.

Replace Formatter PCA. 64 error 4000/4050/4100/5000/8000/8100 only: A scan buffer occurred - if it persists replace formatter. 66.xx.yy error 4000/4050/4100/5000 only: An error occurred in an external paper handling device, stapler/stacker. Press SHIFT+CONTINUE to clear. If error does not reappear, replace RAM expansion card. 3. Thank you, Matteo Parpagiola 2.

TheGo4download 53,185 views 2:57 Fixing a Paper Jam - HP LaserJet 1020 Printer - Duration: 6:54. Incorrect cable hookup or bad I/O port in computer. Check replace SIMM's 61 Service 2686A/D, II, IID, IIP, IIP+, III, IIID, IIIP, 4P Replace formatter PCB 61 Memory IIISi, 4Si, 4V Bad SIMM memory. IIISi/4Si Only: 1.