Home > Hp Color > Hp Color Laserjet 3600n Error Message 54.17

Hp Color Laserjet 3600n Error Message 54.17

Turn the printer off/on to attempt to clear or reset the message. This is accomplished the same way as a Quick Calibration. You save me. Well the black was first to go and when we replaced it the printer restarted and wouldn't exit startup calibration. http://technewsonline.net/hp-color/hp-color-laserjet-3600n-error-10-92-00.html

Follow the steps below: Clean the color cartridge contacts. Calibrate the printer. 54.20 errors: Check the connection. Any idea? If no luck, there is a "Restore Factory Settings" option: Menu; Configure Device; Resets; Restore Factory Resets. http://h30434.www3.hp.com/t5/Inkjet-Printing/Color-Laser-Jet-3600-error-54-17/td-p/5068825

This gets you into the maintenance screen and you will see "NVRAM INIT" on the Display Screen Press the "Down" Arrow once until "Skip Calibration" shows. Thanks again….. Reply Dennis Stefan on January 28, 2015 at 5:30 pm I have been using different methods to correct the problem of continual re calibration. Judith Rickard Reply Chris on December 17, 2015 at 1:59 pm thanks, mike : ) I just read your instructions to a friend.

Hope this helps, Mike Reply Anja on July 18, 2011 at 9:45 pm Hey Mike, thanks so much for all this information, it saved us 400€. Check the light guide and clean it if necessary. It's worth a thousand words. Lift the registration flap and verify that the OHT sensor is not blocked. 3.

Reply Bonnie Burn on July 10, 2011 at 3:09 am Mike, You are wonderful! You may be close to that point. Anyhow, I can print, following your instruction each time when I start. Replace the DC controller.

Close the printer, wait 10 to 15 seconds, then look at the LCD display. If found any damage?, Replace it.3. Replace the colour registration detection assembly. 54.5 errors: Check the connections. Wiggle a VERY small amount while pulling firmly.

Reconnect J1020 on DC controller.Check cable end condition.5. http://www.mikekrauss.com/hp-3600n-constantly-calibrating-fix/ Specialist in HP Laser Printers, Parts and Service Home | About Us | Repair Services | Hp Error Codes | Technical Support | Delivery | Privacy Policy | Returns Policy | or when I press the Menu button. Reply Andre Grenier on November 22, 2013 at 11:37 pm Thank you so much Mike.

The printer kept running and running so we turned it off hoping that the next morning when we turned it on everything would be fixed - no such luck. his comment is here It first started with a broken cartridge lock lever. THANK you for figuring this out! Let us know how it works out.

  1. Remove the Black cartridge and look for the slit.
  2. Some one stated it was due to the color cartridges are no HP would that do it?
  3. Remove and reinstall the supply, replace the supply. 2.
  4. If the LCD display reads Remove and Check Print Cartridges , replace the black or photo cartridge.
  5. Video Photos Link Add Upload Upload × × Draw a box over the problem!!

Replace the print cartridge interface for the cyan/black cartridge. Create your Spare Parts List. PDF Manual Hp6940.pdf. this contact form Tyty Reply Eugene on January 26, 2012 at 4:45 am Thank you very much..

I replaced the yellow cartridge AND put one of the Cyan cartridges back in and it finished the calibration completely. Reply Mike on February 17, 2011 at 2:36 am Hey Paul, Did you start getting the "stuck in calibration" after replacing one or more of the cartridges. Reply 0 0 MartinHeidelber Top Student Posts: 3 Member Since: ‎08-20-2013 Message 3 of 3 (4,309 Views) Report Inappropriate Content Re: Color Laser Jet 3600 error 54.17 Options Mark as New

I will difinitely keep up with this thread, in case this happens again.

So I ordered all four colors (you can do the math cost wise). I know mine started after replacing the black cartridge. This error most commonly occurs when: 1. Use a lint free wipe (or QTip) to wipe the dust off the optics.

The right stall has the gray latch. I remember the LaserJet 4600 had a reset that involved opening the front cover and pressing the engine test button for 20 seconds. I'm guessing this will allow the printer to function even if a toner cartridge is empty. navigate here Expand Popular Questions 6 Answers HP product assistant HP Photosmart C6180 All-In-One... 31 Answers No HP devices detected.

Thanks for your input - Mike Reply kelly on November 3, 2011 at 5:50 pm I do the first two steps but nothing happens when I press the up arrow once. Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts or does it get sent to the print spooler and then lost in cyberspace?